Specification: Firefighting Product Consistency Check Requirements

September 09, 2020

News Related Keywords: No tags.

4.3 to 4.8 and Chapters 6 and 7 of this standard are mandatory, and the rest are recommended.

This standard was drafted in accordance with the rules given in GB/T 1.1-2009 .

This standard was proposed by the Ministry of Public Security Fire Department.

This standard is under the jurisdiction of the National Fire Protection Standardization Technical Committee Subcommittee on Fixed Fire Extinguishing Systems (SAC/TC 113/SC 2) .

This standard is drafted by: Ministry of Public Security Fire Products Conformity Assessment Center.

Participated in the drafting of this standard: Ministry of Public Security Tianjin Fire Research Institute, Ministry of Public Security Shanghai Fire Research Institute, Shenyang Fire Research Institute of the Ministry of Public Security, Ministry of Public Security Sichuan Fire Research Institute, Xi'an Sencel Electronics Co., Ltd., Shanghai Jindun Fire Safety Equipment Co., Ltd., Foshan Gui'an Fire Protection Industrial Co., Ltd. and Shenyang Fire Fighting Electronic Equipment Factory.

The main drafters of this standard are: Dong Jingfei, Yang Zhenming, Qu Li, Jin Yizhong, Lu Hao, Liu Lianxi, Yu Wei, Liu Cheng, Feng Wei, Zhang Decheng, Zhang Shaojun, Cheng Daobin, Wang Xuelai, Li Lihong, Liu Yuheng, Shen Jianmin, Li Ning, Zhang Lisheng, Wang Yanfu, Kang Weidong, Hu Qunming, Fu Ping, Li Yi, Bai Diantao, Zhou Xiangyi, Huang Juntuan.

This standard is the first release.

introduction

This standard is based on the Regulations of the People's Republic of China on Certification and Accreditation and the "Regulations on the Supervision and Administration of Fire Products" jointly issued by the Ministry of Public Security, the State Administration for Industry and Commerce, and the General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China. It is formulated to meet the needs of consistency inspection of fire products.

The issuance and implementation of this standard is of great significance for improving the quality assurance ability of fire-fighting product producers and carrying out fire-fighting product certification work on an impartial, standardized, and effective basis.

1 range

This standard stipulates terms and definitions, general rules, methods, judgments, and treatments for the consistency check of fire products.

This standard is applicable to the consistency check of fire products for the initial factory inspection and post-certification supervision and management of fire protection product certification, and can also be used for the product consistency check of various fire product quality supervision work.

2 normative references

The following documents are indispensable for the application of this document. For dated references, only dated versions apply to this document. For undated references, the latest version (including all amendments) applies to this document.

GB/T 19000 Quality Management System Foundation and Terminology

GA 1035 General Requirements for Factory Inspection of Fire Products

3 Terms and Definitions

The following terms and definitions as defined in GB/T 19000 and GA 1035 apply to this document.

3.1 type test type examination

All-item inspections conducted to verify conformity of the product's technical performance indicators with product standards are usually performed on representative samples.

3.2 Product consistency

The degree of conformity of the mass-produced product and the certified type inspection sample.

Note: Product consistency requirements are regulated by the product certification implementation rules, relevant standards and relevant requirements of the certification body.

3.3 Product Characteristics product characteristic

The product itself has features such as appearance, size, function, and performance, as well as special designs such as key designs, structures, processes, and formula ratios.

3.4 product characteristics document product characteristic document

Technical data describing product characteristics, including documents, drawings, photos, software, etc.

4 General

4.1 Inspection purpose

Conformity inspections are conducted on the product nameplate mark, product key parts and materials, and the degree of conformity of product characteristics with respect to mass-produced certified products and type-examination qualified samples, in order to determine the effectiveness of product consistency control procedures and product quality. Continuing to meet certification standards provides a key basis.

4.2 Check Type

Fire product consistency check is divided into initial inspection and post-certification supervision and inspection.

4.3 Inspection Guidelines

4.3.1 Fire product consistency check should be implemented in accordance with inspection guidelines. The inspection criteria are the basis for determining the scope of conformance inspections, product nameplate markings, key product and material, conformity of product characteristics, and sampling units.

4.3.2 The inspection criteria mainly include:

a) certification application;

b) certification certificate;

c) type inspection report issued by a certification body or designated inspection agency;

d) product identity document certified by the certification body;

e) certified product standards;

f) certification implementation rules;

g) confirmation of product consistency changes;

h) Contents, procedures, methods, and special requirements of the certification body's consistency check on fire-fighting products.

4.4 Inspectors

Inspection of fire product consistency shall be conducted by professional inspectors.

4.5 Planning and Preparation

4.5.1 The planning and preparation before the inspection mainly includes:

a) The professional division of the inspection team;

b) data review;

c) check the scope of determination;

d) inspection plan preparation (usually incorporated into the factory inspection plan, inspection of the sales market, installation and use sites shall be separately prepared);

e) Check the preparation of job documents, checklists and other working documents.

4.5.2 The data review should focus on the following according to the inspection criteria:

a) the professional characteristics of the product;

b) Compliance of the certification application, type inspection report, product characteristic file;

c) whether the sample or certified product has changed or changed.

4.5.3 The scope of the inspection should meet the following requirements:

a) The initial inspection of product conformity only relates to the products that apply for certification;

b) Post-certification surveillance checks cover all certified products covered by the certificate.

4.6 Check Content

4.6.1 The consistency check of the nameplate mark should include:

a) product name;

b) Specifications and models;

c) manufacturers, factories, licensees (if necessary);

d) signs, signs, etc. to be applied in accordance with relevant regulations, standards or documentation requirements;

e) warning language (if necessary);

f) instructions and warnings for installation, instructions and warnings for use in the instructions;

g) Use language (Chinese).

4.6.2 The consistency check of the key components and materials of the product shall include:

a) product name;

b) Specifications and models;

c) manufacturers, factories;

d) Technical parameters (if necessary).

4.6.3 The consistency check of product characteristics should include:

a) The key design of the product;

b) Formulation ratio of the product;

c) the key process of the product;

d) Internal and external structures of the product.

4.6.4 The specified test of product characteristics should include:

a) inspection items specified by the certification body;

b) Other product safety features, such as protection against electric shock, electromagnetic compatibility, environmental pollution, and hazardous substance content.

4.6.5 The content of the fire product consistency check shall also include the specific provisions of the certification implementation rules and attachments, the special inspection contents stipulated by the certification body, and other inspection contents determined by the inspection team according to the site conditions.

4.7 Change of Product Consistency

4.7.1 The factory shall establish and implement procedures and regulations for the effective control of product nameplate markings, key components and materials, product characteristics, and other changes affecting product consistency.

4.7 2 Factory's Change of Conformity of Certified Products The control procedures and rules shall be reviewed and approved by the certification body.

4 7.3 When the factory intends to change the key components, materials and product characteristics of the certified product, it shall carry out the inspection according to the inspection items specified by the certification body and related requirements. After the inspection is qualified, it shall be approved by the certification body before being changed. The change request data and the certification body's approval document should be kept.

4.7.4 Without the approval of the certification body, the factory shall not put a certification mark on the products that have been changed.

4.8 Other requirements

For fire-fighting products manufactured by OEM factories in any form, the contents of the product consistency check specified in 4.6 shall not be deleted.

5 methods

5.1 Sampling method

5.1.1 Sampling can be done at any of the following locations:

a) the finished product library;

b) appropriate process links (if necessary);

c) the end of the production line;

d) sales market;

e) Installation and use site.

5.1.2 Each certification unit draws at least one representative sample.

5.1.3 Sampling should be carried out by the inspectors specified in 4.4 .

5.2 Inspection Methods

5.2.1 The inspectors shall check the consistency of the product by means of observation, measurement and comparison against the inspection criteria.

5.2.2 For the consistency check of the nameplate mark, the product nameplate mark, certification mark, firefighting product identity information mark, outer package printing and instruction content shall be checked.

5.2.3 In order to check the consistency of key components and materials of the product, the manufacturer, specification, type, grade, and technical parameters of the raw materials and components should be checked. When the identification of key components or materials cannot be verified, relevant information on the manufacturer, specifications, models, grades, and technical parameters in the procurement record shall be traced, and if necessary, verification may be made through testing methods.

5.2.4 For the consistency check of product characteristics, the key design, formula ratio, key processes, internal and external structures of the product should be inspected. The inspection shall be carried out by comparison with physical objects, drawings, photographs, inspectors' professional judgments, on-site production operations, and other methods.

5.2.5 For the specified inspection of product characteristics, the inspection project shall be designated by the certification body and carried out by the inspection team at the factory site. If necessary, the inspection agency designated by the certification body may also perform the inspection.

5.3 Inspection records

The inspection team shall fill in the inspection records, including records of consistency inspection of fire products and records of consistency inspection and control of fire products. Fire products consistency check recorded in Appendix A, the fire control product consistency check recorded in Appendix B.

6 determination

6.1 The results of the consistency check of fire products are classified into conformity and non-conformity.

6.2 The results of the consistency check of the fire-fighting products confirm that the products are in accordance with the inspection criteria and that the conformity of the products is in line with the requirements.

6.3 If one of the following conditions exists, the consistency of the product is judged to be inconsistent:

a) The product nameplate mark, instruction content, etc. are inconsistent with the type inspection sample;

b) The key design of the product, the formulation ratio, the key design of the key process and type inspection sample, the formulation ratio, and the key process are inconsistent;

c) The internal and external structure of the product does not match the type inspection sample;

d) Failure of the specified test of product characteristics;

e) violation of the specific provisions of the certification implementation rules;

f) Violation of the special inspection requirements of the certification body;

g) Changes involving product consistency have not been approved by the certification body;

h) Other inconsistencies with the inspection criteria.

7 processing

7.1 If the product consistency is consistent, the inspection team shall submit the inspection record to the certification body according to the specified time limit.

7.2 5.4.7 accordance with the provisions of the unqualified nature of the GA 1035, the product does not meet the consistency of the nature of a gross failure, the inspection team should issue a major non-conformity report. If it belongs to the initial inspection, the inspection shall be suspended immediately; if it belongs to post-certification supervision, the inspection team shall, on behalf of the certification body, withdraw the certification certificate, seal the certification mark, and require the factory to immediately stop production and stop the use of the certification mark.

7.3 The factory that has been determined to be inconsistent with the product shall be rectified according to the certification rules and requirements of the certification body. After the completion of the rectification, a re-inspection application shall be submitted to the certification body in accordance with the prescribed procedures.

7.4 Products that do not conform to the consistency of the products found in circulation and use areas shall be treated as uncertified products in accordance with relevant laws and regulations.

The information in this article comes from the Internet and was reorganized and edited by China Rescue Equipment Network.

Pe Plastic Sheetfull name is Polyethylene Sheet.

Physical properties: PE  plastic Sheet is the most simple structure of the macromolecular organic compounds, the world's most widely used polymer materials, composed of ethylene polymerization, depending on the density is divided into high density polyethylene, medium density polyethylene and low density polyethylene.


Classification of PE Sheet
(1) LDPE Sheet 
       Low density polyethylene Sheet (also known as high pressure polyethylene Sheet)
       
(2) LLDPE Sheet
       Linear low density polyethylene

(3) MDPE Sheet
       Medium density polyethylene
       
(4) HDPE Sheet
       High density polyethylene (also known as low pressure polyethylene)


 (5) UHMWPE Sheet 

      Ultra high molecular weight polyethylene

 (6)Modified polyethylene sheet
      Chlorinated polyethylene (CPE) and crosslinked polyethylene (PEX)

 (7)Ethylene - ethylene copolymer
     Ethylene/propylene copolymer (plastic), EVA, ethylene, ethylene butene copolymer - other olefins, such as octene POE, cyclic olefin copolymer, ethylene/unsaturated ester copolymer (EAA, EMAA, EEA, EMA, EMMA, EMAH).
Polyethylene, which has a molecular weight of 3 million to 6 million, is known as UHMWPE.

Ultra high molecular weight polyethylene is very strong and can be used for body armor.


Applications:
1. Papermaking industry: suction box board, scraper, molding plate, bearing, gear;
2. Mining industry: charging barrel, abrasive and adhesive-resistant back lining for warehouses;
3. Chemical industry: acid pump, filter plate, worm gear, bearing;
4. Food industry: packing machinery parts,   bottle guide, screw, wear plate, slide way, stud weld, roller and other transmission parts;
5. Textile industry:buffer board;
6. Food processing industry: chopping block, refrigerating plant;

7. Wharf: anti-collision board.


Advantages: 
1. Acid and alkali resistance, resistance to organic solvents 
2. Excellent electrical insulation and static resistance
3, Can still maintain a certain touness even at low temperature
4. Extremely high impact strength
5. Low friction coefficient
6. Non-toxic
7. Low water absorption
8.Lower density than any other thermoplastic plastics (<1g/cm3)

 Disadvantages:
 PE Plastic sheet have Weak mechanical property, air permeability, easy deformation, easy ageing, brittle, brittle less than PP, easy stress cracking, surface hardness, easy to scratch.
Difficult to print, in printing, surface discharge treatment, cannot electroplating, the surface has no luster.
       
       
Specification: the diameter of the PE rod can be produced from 2mm to 250mm. The conventional length is 1000mm, and the length is unlimited.
The thickness of PE sheet material can be produced from 0.3mm to 1.9mm, the normal width is 600mm, the width cannot exceed 1200mm, the length is not limited.
The thickness of plate can be produced from 2mm to 180mm, the usual specification of 2-10mm is 1000mm* 2000mm, and the commonly used specification of10-180mm is 600*1200mm.PE sheet can also be customized according to requirements, and the width cannot exceed 1200mm, and the length is not limited
 

Color: natural color is wax white, also can be customized black and color, the order of the color to order is 500KG.


Modified varieties: PE sheet/rod can be added to the fiberglass, copper powder and molybdenum disulphide to enhance the bar.
Add antistatic agent to the permanent antistatic electric bar, and the volume resistance value is between 6 to 9 power of 10.Add flame retardant to the flame retardant rod from UL 94V-0 to HB flame retardant grade, and other modification requirements are required to customize various additional properties according to the actual use of the customer.


Combustion characteristics:

Combustion situation: easy

Combustion flame status: molten drop, yellow lower blue

After the fire: continue to bur

Smell: the smell of wax burning

    

 Product certification: most environmental certification reports and safety reports for raw materials, such as SGS report, CTI report, UL report, MSDS safety information, etc.


 






PE Plastic Sheet

Pe Plastic Sheet,White Pe Plate,Standard Material Pe Plastic,Transparent Pe Plastic Sheet

Dongguan Noegem Plastic Products Co.,Ltd , http://www.noegempLastic.com